SteelThumb

Procedure · OKF v0.2

Treat and inoculate prepared paddy-straw mushroom compost

Historical indoor thermal-treatment sequence with operational prerequisites retained.

Status: draft 6 claims License: MIT Rev: 54d2abbe6163 Raw OKF (.md) Source on GitHub

Treat and inoculate prepared paddy-straw mushroom compost

This task starts with prepared paddy-straw compost for Volvariella volvacea. It does not turn unprocessed straw directly into a ready bed. Obtain a complete compost formulation and preparation specification first; the earlier bulletin section's lime identity and bran percentage basis need clarification before a reproducible recipe can be issued.

Preconditions

Use labeled fresh spawn, measured compost mass and moisture basis, shelving or a treatment tunnel, and an established steam-equipment operating procedure. Define temperature-probe placement, treatment uniformity and when the holding clock begins with the equipment/process provider before use. The source gives thermal settings without those validation details; a room-air reading alone is not demonstrated to establish treatment throughout the compost. This is a partial operational reference until those decisions are resolved.

Load, treat and cool

Spread prepared compost 5–10 cm thick on shelves, using the thinner end in summer and thicker beds in winter; level lightly.1

After 8–12 hours on the shelves, introduce steam; the bulletin specifies 65 °C for six hours for paddy-straw compost.1

After steaming, keep the room closed at 50 °C for 24–36 hours, then let the substrate cool naturally.1

Inoculate when the compost reaches about 35 °C.1

Keep the substrate branch fixed: the bulletin gives a different heat/time pair for cotton waste. Do not substitute that treatment or combine it with these paddy-straw settings. These are pasteurization/conditioning directions, not proof of sterilization. Record measured temperatures, timing, bed depth and departures from the selected process.

Inoculate and continue

Use fresh spawn at 1.4% of compost dry weight, or the separately stated 0.4% of wet weight.1

Insert spawn pieces 2–2.5 cm deep, spaced 12–15 cm apart; replace displaced compost and cover the bed with thin plastic.1

Select one mass basis and document it. The two stated percentages are alternatives; they are not equivalent for every moisture content. Obtain the compost dry-mass value or the method's moisture specification before calculating a batch amount. Do not count dry straw before composting as measured dry compost without a justified basis.

Use the indoor planning guide for the same source method's subsequent room conditions and its warning about watering primordia. Record colonization and abnormal growth; missing or uneven growth calls for review of treatment, cooling, spawn and moisture records, not an automatic repeat chemical application. Contamination response, exact ventilation/light controls and current local process confirmation remain unresolved. The harvest task supplies the later physical picking action. Source notes.

Connected concepts (5)

Paddy straw mushroom

Volvariella volvacea: initial Indian cultivation references and physical harvest task.

applies to · Crop
Inspect OKF v0.2 Claims & Evidence (6 claims, 1 sources)
#bed recommendation compost layer depth: 5–10 cm (Season-dependent indoor shelf bed, not outdoor bundle height.)

Spread prepared compost 5–10 cm thick on shelves, using the thinner end in summer and thicker beds in winter; level lightly.

Applicability: Historical indoor compost method for cultivated Volvariella volvacea; prepared paddy-straw compost branch, not raw straw bundles or cotton-waste treatment.

Evidence: supports via nrcm-paddy2007 (Printed p. 22, Bedding and Pasteurization)

#steam recommendation paddy straw pasteurization temperature: 65 degC (Six-hour treatment; source does not specify probe placement or hold-start criterion.)

After 8–12 hours on the shelves, introduce steam; the bulletin specifies 65 °C for six hours for paddy-straw compost.

Applicability: Historical indoor compost method for cultivated Volvariella volvacea; prepared paddy-straw compost branch, not raw straw bundles or cotton-waste treatment.

Evidence: supports via nrcm-paddy2007 (Printed p. 22, Bedding and Pasteurization)

#condition recommendation poststeam conditioning temperature: 50 degC (Historical indoor conditioning stage; duration retained in statement.)

After steaming, keep the room closed at 50 °C for 24–36 hours, then let the substrate cool naturally.

Applicability: Historical indoor compost method for cultivated Volvariella volvacea; prepared paddy-straw compost branch, not raw straw bundles or cotton-waste treatment.

Evidence: supports via nrcm-paddy2007 (Printed p. 22, Bedding and Pasteurization)

#cool recommendation compost temperature at spawning: 35 degC (Approximate compost temperature, distinct from later room control.)

Inoculate when the compost reaches about 35 °C.

Applicability: Historical indoor compost method for cultivated Volvariella volvacea; prepared paddy-straw compost branch, not raw straw bundles or cotton-waste treatment.

Evidence: supports via nrcm-paddy2007 (Printed p. 22, end of Bedding and Pasteurization)

#dose recommendation spawn rate dry basis: 1.4 percent (Spawn mass relative to compost dry mass; wet-basis alternative is not additive.)

Use fresh spawn at 1.4% of compost dry weight, or the separately stated 0.4% of wet weight.

Applicability: Historical indoor compost method for cultivated Volvariella volvacea; prepared paddy-straw compost branch, not raw straw bundles or cotton-waste treatment.

Evidence: supports via nrcm-paddy2007 (Printed p. 22, Spawning)

#insert recommendation spawn insertion depth: 2–2.5 cm (Indoor compost method; lateral spacing retained in statement.)

Insert spawn pieces 2–2.5 cm deep, spaced 12–15 cm apart; replace displaced compost and cover the bed with thin plastic.

Applicability: Historical indoor compost method for cultivated Volvariella volvacea; prepared paddy-straw compost branch, not raw straw bundles or cotton-waste treatment.

Evidence: supports via nrcm-paddy2007 (Printed pp. 22–23, Spawning, text continued beneath Figure 20)