Grow leaf lettuce in aerated deep-water culture
This route combines Cornell’s aerated home DWC guidance with UMN’s leaf harvest and hygiene guidance. It is an editorial synthesis, not a tested combined protocol. Cornell’s experiments used head lettuce as a proxy for leafy greens; no named loose-leaf trial or guaranteed picking count is asserted.
Prerequisites and establishment
Assemble the aerated floating-support system. Obtain identified lettuce seed, fresh rockwool seed cubes and their instructions, a seed flat, clean suitable water, a complete hydroponic fertilizer with a readable recipe, pH/EC equipment, suitable pH adjustment products, and harvest tools. Record cultivar, reservoir volume, lamp setup, actual spacing and product recipe. Resolve missing product instructions before dosing.
Select a lettuce cultivar identified by its seed supplier as suitable for hydroponics; retain the cultivar’s mature spacing guidance.1
For the Cornell rockwool branch, soak cubes in nutrient solution for 10–15 minutes, then sow one lettuce seed per cube and place under light.2
Water the seed cubes daily or as needed to prevent drying; remove accidental double lettuce seedlings.2
Transplant when seedlings have three to four true leaves and roots are visible at the bottom of the cube; keep the cube bottom in contact with nutrient solution when placed in the floating support.2
Use the seed/cube supplier’s directions for seed placement; the inspected guide does not establish one numerical depth for every cube. Use observable transplant readiness rather than assuming the commercial day-11 schedule. Keep the air pump running and the float moving freely.
Nutrients and care
Use a complete conventional hydroponic fertilizer and its vegetative or general-growth recipe for the measured water volume; dissolve each component separately into water before adding the next.2
For the Cornell home leafy-green route, adjust the mixed nutrient solution to pH 5.5–6.0 using a hydroponic pH kit or calibrated meter and suitable adjustment products.2
Check pH and EC once or twice per week if possible; Cornell’s DWC guide calls for nutrient-solution top-ups every one to two weeks or as needed.2
EC measures all dissolved salts, including those already present in source water; measure the source water before mixing fertilizer.2
Use the product-label dilution and mixing order; do not mix undiluted concentrates together. Follow the adjustment product’s label, mix and remeasure. No acid/base dose is established without the actual product and source-water chemistry. EC is not a nutrient recipe: confirm the expected final EC with the chosen lettuce-fertilizer instructions. Investigate unexpectedly high source-water EC through water analysis before adding more fertilizer. The source comparison preserves different published targets and check frequencies.
Editorial daily observation plan: inspect bubbles, float movement, cube/root contact, solution level and leaf condition. The source’s longer top-up interval does not justify letting roots lose water contact. Record each top-up’s volume, nutrient recipe and measurements. Unexpected drift or wilting calls for an immediate check, not waiting for the routine interval. This aerated method does not use a passive no-refill rule.
Climate and investigation
For lettuce bolting management, Cornell gives air below 80 °F or water below 68 °F as control measures.2
Thin, stretched plants can reflect insufficient light or crowding; examine spacing and increase available light when low light is the problem.2
Distinguish a flower stalk from generally stretched thin foliage. Without a stalk, check crowding and canopy light against the light target; adjust the identified problem and compare subsequent leaf growth. With flowering, review air/water temperatures and cultivar suitability and plan replacement plants; cooling does not promise to reverse flowering.
For wilt, first inspect bubbles, root contact and solution measurements. Brown roots with continued decline need diagnosis; color alone does not establish Pythium. Record root appearance and operating conditions and seek local plant-disease assistance for unexplained decline. The disease response below applies to diseased plants, not every wilt episode.
Remove infected plants; when root rot affects a shared solution, Cornell advises considering ending the crop, sanitizing and restarting with new plants and solution.2
Harvest and reset
For repeated leaf-lettuce harvest, cut mature lower leaves and allow the plant to continue growing.1
Harvest with clean hands, cleaned and sanitized tools and containers, and minimize nutrient-water splashes onto edible leaves.1
Observe whether new usable leaves continue to form; there is no guaranteed harvest count. Editorial endpoint: replace plants when continued harvest is no longer useful or plants bolt. Rinse produce before consumption as UMN advises; rinsing is not a remedy for known contamination.1
Between plantings, remove residues, wash system components with detergent, rinse with potable water, and sanitize the equipment.1
Follow a sanitizer label appropriate for the equipment and food-growing use, including concentration, contact time and any required rinse. The inspected source’s generic bleach spoon-volume example is not adopted because the actual product strength must be known. Keep cleaning products separate from crop nutrient mixing.
Remaining work
Confirm cultivar performance, source-water composition, nutrient product and lamp coverage for the actual site. The route does not size an air pump from a dissolved-oxygen test, establish full climate control or promise year-round production in an uncontrolled room. Regional energy feasibility, detailed pathogen differentials, NFT, aeroponics and aquaponics remain separate research. Leaf-lettuce crop hub.