SteelThumb

Procedure · OKF v0.2

Care for and harvest land cress

Investigate moisture and leaf damage, then choose repeated picking or a terminal rosette cut.

Status: draft 5 claims License: MIT Rev: 54d2abbe6163 Raw OKF (.md) Source on GitHub

Care for and harvest land cress

Retain the sowing route and stock identity. Have water, clean sharp scissors or a knife, and a clean collection container. Tool and hygiene choices are editorial implementation of the picking/cutting instructions.

RHS includes land cress among repeat-cut salads and recommends keeping seedlings weed-free and well-watered, with regular watering after cuts.1

RHS identifies small rounded leaf holes and beetles jumping when disturbed as clues to flea-beetle feeding.2

RHS says insect-proof mesh may exclude flea beetles from susceptible crops.2

UF/IFAS starts leaf picking on established land cress about 4 inches high, leaving stems and roots intact for further leaves.3

Johnny’s harvests full-size upland-cress rosettes below the basal plate; its baby-leaf branch instead cuts above that base when leaves reach the desired size.4

Inspect and follow up

Editorial moisture check: compare wilt in dry soil with wilt that persists while soil is wet. Examine actual root-zone moisture and drainage before adding water. Maintain moisture for growth, but do not infer a standing-water requirement from the common name cress. Persistent collapse needs local root/plant-health diagnosis. Nutrient product and rate remain local inputs; yellow foliage alone does not establish a deficiency.

The RHS crop profile lists flea-beetle susceptibility. Confirm visible feeding signs and inspect for beetles before responding. For exclusion, check a clean crop, cover integrity and edges; these are editorial implementation. Mesh does not remove insects already enclosed. Compare fresh leaves for new damage after adjustment, and refer unexplained severe loss to local diagnosis.

Choose the harvest endpoint

For repeated picking, snip selected sound leaves at their stalks while retaining the central growing region and stem/root system. The snipping action and taking only a few leaves at a time are editorial implementation of UF/IFAS selective picking, not a measured removal fraction. Observe fresh growth before repeating. Pause if the retained plants are declining or not replacing foliage.

For whole rosettes, hold leaves clear and cut below the basal plate. Treat that as a terminal harvest of that plant; do not promise repeat production from a removed growing base. The baby-leaf cut is a separate dense-crop route whose complete sowing and nutrition inputs are not authored here.

Flowering in a retained second-year plant can match the documented lifecycle; distinguish that from insect holes or wilting. Plan new labeled sowings for continued leaf production rather than infer disease from a flower stalk. No fixed repeat interval, yield, storage life or microgreen sanitation protocol is established. Crop · Sources and gaps.

Connected concepts (3)

Land cress / upland cress

Barbarea verna for repeated leaves or whole rosettes, with separate Florida and supplier sowing routes.

applies to · Crop
Inspect OKF v0.2 Claims & Evidence (5 claims, 4 sources)
#care recommendation

RHS includes land cress among repeat-cut salads and recommends keeping seedlings weed-free and well-watered, with regular watering after cuts.

Applicability: General UK salad guidance explicitly including land cress, not a crop-specific irrigation trial.

Evidence: supports via rhs-salads (Suitable for; How to sow, steps 6 and 8)

#flea-signs descriptive

RHS identifies small rounded leaf holes and beetles jumping when disturbed as clues to flea-beetle feeding.

Applicability: General UK brassica-family diagnostic guidance; not identification from holes alone.

Evidence: supports via rhs-flea (Quick facts; Symptoms)

#exclusion recommendation

RHS says insect-proof mesh may exclude flea beetles from susceptible crops.

Applicability: General flea-beetle exclusion applied to land cress, which its RHS profile lists as susceptible.

Evidence: supports via rhs-flea (Management)

#leaf-picking recommendation plant height at picking: 4 in (Approximate established plant height, not leaf length or cutting height.)

UF/IFAS starts leaf picking on established land cress about 4 inches high, leaving stems and roots intact for further leaves.

Applicability: Barbarea verna in UF/IFAS Florida garden guidance, HS681, reviewed 2018; regional historical route.

Evidence: supports via uf-land-cress (Page 1 — Use)

#rosette-cut recommendation

Johnny’s harvests full-size upland-cress rosettes below the basal plate; its baby-leaf branch instead cuts above that base when leaves reach the desired size.

Applicability: Johnny’s Upland Cress soil-grown rosette branch, distinct from its other cress species and baby-leaf density.

Evidence: supports via johnny-cress (DIRECT SEEDING — Upland Cress harvest sentences)